3D Printing Stack Exchange
3D Printing Stack Exchange

Most Popular

more tags
1500 questions
4
votes
1 answer

Export firmware as a .hex

Because .hex files can be installed without any need of an Arduino (serving as an ISP) to flash the firmware on Creality machines I was wondering, if firmware compiled via some other means (for example the Repetier firmware or Arduino) could be…
Trish
  • 21,915
  • 12
  • 50
  • 101
4
votes
3 answers

Would adding fiberglass packaging tape to a bowden tube be beneficial?

I came across this suggestion on the klipper github, https://www.facebook.com/groups/Hypercube.Evo/permalink/192106034761003/. In order to reduce the stretching in the bowden tube you can add fiberglass packaging tape lengthwise along the tube. This…
Perplexed Dipole
  • 709
  • 1
  • 6
  • 14
4
votes
2 answers

What is a masterspool?

Recently, I have heard people talking about masterspool, when talking about 3D printing filament. What exactly is master spool? Where did the idea come from and when? Is it being widely adopted? Or to be specific, how many…
Greenonline
  • 6,308
  • 8
  • 36
  • 65
4
votes
1 answer

What printer is this?

I've been watching this video 3D printing guides: Calibration and why you might be doing it wrong and at the start (at 0:30) three of the first Reprap printers are mentioned (and shown): Darwin; Prusa Mendel, and; what sounds to be "Cells". Here…
Greenonline
  • 6,308
  • 8
  • 36
  • 65
4
votes
2 answers

But ... skateboard bearings have OIL in them, and oil is ... bad?

I see plans for various spool holders, either for PLA in the open, or for whatever filament in a dry box, that use 608 bearings. Elsewhere, I see warnings not to oil your filament to make it go through the extruder better, because problems going…
nebogipfel
  • 299
  • 4
  • 7
4
votes
2 answers

Is there a table or list of tare weights of empty spools of various manufacturers?

It would be helpful to me if I knew in advance how much the empty filament spool weighs. Not having emptied any spool yet, I can't contribute data points, but has anyone compiled a list of empty weights from various manufacturers and sizes?
nebogipfel
  • 299
  • 4
  • 7
4
votes
2 answers

Is the 110 m length accurate for 3.0 mm 1 kg spool?

I've been seeing the 330 m and 110 m length estimates for 1.75 and 3.0 mm spools (of PLA, presumably). But a moment's thought staring at that will raise an obvious question. Using πr², we get the area of the filament in square millimeters (rounding…
nebogipfel
  • 299
  • 4
  • 7
4
votes
2 answers

First layer of print comes out poorly even when placed on a raft (which prints fine)

I'm printing PLA with the Creality Ender 2 and my print comes out totally fine with the exception of the first layer. Here's the weird part though, if I place a raft or a brim below/around the print - the raft or brim will print perfectly cleanly.…
Matt
  • 223
  • 1
  • 4
  • 9
4
votes
2 answers

What are the specifications of the dual voltage controller of the Ender 3/CR-10?

Following on from What level of voltage does the Creality Ender-3 run at? Dave's answer states that both 12 V and 24 V can be used on the controller board. It also goes on to say that the controller board is used in both configurations in two…
Greenonline
  • 6,308
  • 8
  • 36
  • 65
4
votes
2 answers

Anet A6 Z-axis min endstop not triggering

I had a Z probe installed but the wires came out of the header so I am trying to use software endstops, but any time I G28 the nozzle will always ram into the bed. I am using Marlin Firmware. Which I am relatively new with. I'm used to having…
seraphina
  • 143
  • 6
4
votes
2 answers

Cura confused as to what's touching the buildplate?

I'm very new to 3D printing, but so far I've been able to print a couple things off Thingiverse without issue. However, as I'm trying to print another part, I've run into a situation where Cura is totally confused as to what's touching the…
You'reAGitForNotUsingGit
  • 203
  • 1
  • 6
4
votes
1 answer

Baking old PLA spool

Context A while ago I bought a kit for a 3D printer, along with filament etc. however, after some weeks I ran into some mechanical problems and because I had a lot of other things to do at the time I put the project on hold. Now, almost a year…
dragonfly
  • 143
  • 3
4
votes
1 answer

White blocks on LCD screen after Anet A8 power up

I just completed assembly of the Anet A8 and powered it up. Powering up shows white blocks on LED and a series of clicking noise for about three seconds with flashing red LED. During power-up, the following happens: The side heat sink fans start…
DoomerDGR8
  • 215
  • 5
  • 8
4
votes
2 answers

Which outdoor filaments for unheated beds?

I am searching for 3D printing filaments, that are suitable for outdoor purposes, but printable on unheated beds. I will mostly use it for sensor node enclosures (should withstand temperature up to 50°C/120°F) and car accessories (70°C/160°F). If it…
typo
  • 926
  • 1
  • 8
  • 14
4
votes
4 answers

Z-Axis doesn't work only during printing

Problem: Z-Axis doesn't work during a print. It attempts to work, maybe climbs on the Z-Axis, but screws back down. It whines, too. But, Z-Axis DOES work while not printing. It doesn't matter if the bed and nozzle heating or not, if it's not…
RMF
  • 81
  • 5
1 2 3
…
99 100