3D Printing Stack Exchange
3D Printing Stack Exchange

Questions tagged [ender3]

16 questions
4
votes
1 answer

Ender 3 Pro: X-axis moves too much during printing

I got an Ender 3 Pro yesterday and have been having a problem with all of my prints. Whenever the extrusion stops and the X-axis moves, it moves too far. For example, I tried printing a Benchy with 2 skirt lines, and the lines were the right size…
DerFern
  • 141
  • 7
1
vote
0 answers

How to print more accurately 3D cube test?

I have print problems with my Creality Ender 3 S1 and I have calibrated all axes: Belts both X and Y axex Extremes of the X-axis horizontal structure have the same distance to the bottom of the printer Wheels both the X-axis and Y-axis (wheels…
John Miller
  • 11
  • 3
1
vote
2 answers

Ender 3v2 nozzle plunging into bed after finishing mesh (only changed springs)

Yesterday I was printing just fine. Today I put the new springs that I bought from Amazon. Swapped them out, went to level things and my Z-offset was of course way off. I have the Ender3V2-422-BLTUBL-MPC-20230904.bin firmware from mriscoc I homed…
Joleme
  • 11
  • 2
1
vote
1 answer

Ender 3 S1 Pro error "extrude below min temp"

When I start my print it goes to home the z-axis and then I get the error "extrude below min temp" error (I have an Ender 3 S1 Pro)
Mr. Magic
  • 11
  • 1
1
vote
0 answers

How would I fix an under extrusion problem?

Hey all I have an Ender 3 V1 and I have a problem with it under extruding. Its not putting out enough PLA to stick and it just becomes a mess. (Bed has a magnetic PEI plate that only has a few uses) Occasionally it will put out a little more on one…
Nick Vitale
  • 11
  • 1
1
vote
0 answers

How to fix Y axis is off by 30 mm?

I have Ender 3 with Klipper. In my config: [stepper_y] step_pin: PB10 dir_pin: !PB2 enable_pin: !PB11 microsteps: 16 rotation_distance: 40 endstop_pin: ^PC1 position_min: -30 position_endstop: -30 position_max: 200 homing_speed: 50 With this, when…
Alex Buznik
  • 111
  • 2
1
vote
1 answer

G28 X does not home the hotend

I have a classic Ender 3 running Marlin-2.1.1 on a BTT SKR v1.3 board with TMC 2130 drivers. Wifi is connected with ESP3D on an ESP32-CAM board connected to a TFT port. The X endstop is on the left side. When I send G28 or G28 X, the hotend does not…
Hansa G
  • 31
  • 3
1
vote
0 answers

Is it normal that my heated bed has up to 25 °C difference from center to edge?

I have an Ender 3 V2 pro with the Quinly bed adhered to the aluminium bed. I have a hard time getting my prints to stick well. (PLA as well as PETG). We finally found out that only increasing the bed temperature a lot helps a little. Only the edges…
Hacky
  • 679
  • 3
  • 11
0
votes
1 answer

Ender 3 v2 with CR Touch/BLTouch moving down but not up

My Ender 3 v2 with a CR Touch/BLTouch installed is only moving down, but not up! The display shows P Endstop when I try to move below around halfway up the gantry. What's going on, and how do I fix this?
zurgeg
  • 123
  • 6
0
votes
1 answer

The nozzle becomes clogged in the smoothing mode

My nozzle gets clogged when it starts to do smoothing. Settings below:
Мульти студия
  • 1
  • 2
0
votes
0 answers

Ender 3 S1 Pro extruding/jamming on random layers

My relatively new Ender 3 S1 Pro with default extruder started to under extrude and jam on some layers. When it happens I can hear extruder skipping/clicking noises. I printed same g-code multiple times and happened on different layers. I replaced…
kzulis
  • 1
  • 2
0
votes
2 answers

How to fix "SD Init Fail" on Ender 3

My Ender 3 is showing SD Init Fail when the sd card is inserted. I tried rebooting, reformating the card etc. At first, I thought the card is damaged, so I bought a new card. Still the same. I can use the card with the computer without any…
Johnykutty
  • 131
  • 1
  • 5
0
votes
0 answers

Ender 3 CR Touch Bed Levelling X axis offset

I upgraded my Ender 3 with the CR Touch, and updated the firmware (contacted Creality directly to get the correct version). I got Marlin 2.0.6. However when I try the bed levelling feature the first point (nearest to the origin), always starts with…
Fusco Bhonsle
  • 1
  • 1
-1
votes
0 answers

Retract error on ender 3

I'm encountering issues with my Ender 3 printer. During prints, it consistently fails in the middle, displaying "retract 1.0" or similar messages( retract 2.0, 3.0 and sonon. Sometimes shows distance). Despite the extruder motor working, the…
morgan
  • 1
  • 1
-1
votes
0 answers

Weird "Fuzz" on bottom base layer of prints

recently assembled an Ender 3 V2 but I am having trouble printing ANYTHING in general, something always messes up. When printing the bottom layer a print, after the first layer (which sticks well to my glass bed) tiny fuzzy bumps start sticking out…
Kelvin Liao
  • 1
1
2